Vestax PMC-55 Manuel d'utilisateur télécharger pdf (Page 6)

PROGRAM INPUT SECTION

MAX

LINE 1

PHONO 1 LINE 2

MIN

PGM 1

+6dB

(

0dB

)

-24dB

PRE

OUT

POST

OUT

A MASTER B

+6dB

(

0dB

)

-24dB

+6dB

(

0dB

)

-3

-8

-13

(

)

-24dB

LOW

AUX

MASTER 1

C.F. ASSIGN

CUE

EQ CUT

OUT

MASTER 2

MID

TRIM

BAL

INPUT

LINE IN 2

○

BALANCE CONTROL

Adjusts the stereo balance for each PGM channel.

Can be used for adjusting the unbalanced stereo

image caused by strong Anti-Skating setting.

Clockwise rotation from center position increase

volume of R over L channel. Counter clockwise

rotation increase volume of L channel over R.

○

EQ CUT SWITCH

Press this switch to bypass EQ secti

on.

○

EQ (HI, MID, LOW)

Adjusts the HI,MID and LOW frequencies for each

PGM channel. Each band has following

specifications.

HI 8kHz -24dB~ +6dB Shelving type

MID 500Hz -24dB~ +6dB Peaking type

LOW 80Hz -24dB~+6dB Shelving type

○

AUX ASSIGN SWITCH

Used when sending signal to external effect processor

connected to AUX SEND/RETURN (42).

○

MASTER OUT ASSIGN 1, 2

Used to send the signal from each program to either

MASTER OUT 1 or 2 (43). MASTER LOOP is

located on MASTER OUT 1.

○

CROSSFADER ASSIGN

Used to send the signal from each program to either

the crossfader (A or B) or the master directory. A for

left side of the crossfader, B for right side.

○

CUE ASSIGN

Used to send the signal from each program to

monitor section for headphones monitoring. Signal

is sent to CUE OUT (42) too. This allows for

sending signal to external sampling unit connected

to CUE OUT.

○

INPUT FADER

Used to adjust the Input level of each program.

Usually set at the 7-8 position. This is a detachable

fader for the ease of replacement. Replace with IF-

50 when It is worn out.

HOW TO REPLACE THE INPUT FADER

●

Remove four screws which hold the fader unit panel.

●

Take the unit out with the panel

●

Remove a knob and two screws which hold the

fader unit.

●

Carefully remove the multi-cable connector from

the fader unit.

●

Insert the connector to the new fader unit.

●

Replace the knob and the fader unit to the panel

and fix it with screws.

●

Replace the fader unit panel and tighten the

screws.

○

LINE IN 2, 4, 6, 8 (RCA)

Used for line level input. Connect CD player or tape

deck to these jacks. Line level musical instruments

with stereo outputs such as rhythm machine or

sampler are also good for LINE IN. And they are

located on the top panel for quick and easy access.

This is particularly useful for "visiting" equipment.

○

INPUT SELECTOR

Used to select the input (two LINE or one PHONO)

to be sent to each PGM channel.

○

INPUT LEVEL METER

The LED level meters indicate the input signal level

of each PGM channel.

○

GAIN CONTROL

Adjusts the input level of each channel. Set INPUT

FADER (12) to 7-8 position, adjust GAIN so that

INPUT LEVEL METER(3) shows about 0dB.

55/E／面付け 00.9.12 4:44 PM ページ 9

1 2 3 4 5 6 7 8 9 10 11 ... 14 15

Commentaires sur ces manuels

Pas de commentaire

Vestax PMC-55 Manuel d'utilisateur Page 6

Commentaires sur ces manuels

Produits connexes et manuels pour Instruments de musique Vestax PMC-55